A faulty electricity meter does more than stop recording units. It can lead to average bills, disputes over consumption and, if the meter is burnt, a real safety risk at home. Knowing how IESCO meter replacement works helps you report the problem quickly, keep the right evidence and avoid paying for something that is not your fault. The process is regulated, so consumers have clear rights at every step.
This guide walks through the full process: how to recognise a defective or burnt meter, what information to collect, how to register a 118 complaint and use your SDO office, and what happens during inspection and installation. It also explains average billing on a defective meter, who pays the meter cost, how to verify the new meter reading, and why tampering is treated very differently from a normal fault.
How to Recognise an IESCO Faulty Meter
Most meter problems show up either on the meter itself or on your bill. Spotting them early makes IESCO meter replacement faster and keeps your billing record clean.
Common Signs of a Defective Meter
- Blank or washed display: the digital screen is empty, faded or shows random characters. NEPRA’s rules call this a “display wash”.
- Reading not moving: the kWh value stays the same even though you are using electricity.
- Unusual jumps: units suddenly rise far above your normal pattern with no change in usage.
- Error codes or warning lights that stay on.
- Physical damage: cracked glass, a loose or tilted meter, or a missing terminal cover.
Before assuming a fault, compare the meter with your bill using our guide on IESCO meter reading check online. A higher bill is sometimes caused by a late reading rather than a faulty meter.
IESCO Burnt Meter: Safety First
An IESCO burnt meter may show smoke marks, a burning smell, melted plastic or sparking at the terminals. Do not touch it or try to open it. Switch off your main breaker if it is safe to do so, keep children away and call IESCO helpline 118 immediately. A burnt meter is both a supply fault and a hazard, so report it as an emergency rather than waiting for the next bill.
What You Need Before Requesting IESCO Meter Replacement
Having the right details ready saves repeat visits and makes your complaint easier to trace.
Reference Number and Meter Serial Number
- Consumer reference number: the 14-digit number on your bill. See our guide to the IESCO reference number if you cannot find it.
- Meter serial number: printed on the meter body and normally shown on the bill. Matching the two confirms the complaint is about the right meter.
- Last known reading: the last kWh value you saw before the fault, if the display was working.
Documents and Photos to Keep
- A copy of your latest bill. You can download a duplicate IESCO bill if the paper copy is missing.
- Your CNIC, especially if the connection is in your name.
- Clear, dated photos of the meter display, the serial number and any visible damage.
- For a meter that was stolen or damaged in an accident, a written report to the sub-division office, which the rules require you to make immediately.
How to Report an IESCO Faulty Meter
IESCO meter replacement starts with a complaint. You can use more than one channel, and it is wise to keep a written record.
Register a 118 Complaint
Call IESCO’s helpline 118 and report a defective or burnt meter. Give your reference number, meter serial number and a short description of the fault. Ask for a complaint number and note the date and time of your call. Our IESCO helpline guide lists other contact options, and the IESCO complaint guide explains online channels and tracking.
Submit a Written Application at the SDO Office
Your SDO office (sub-divisional office) handles meter replacement in your area. NEPRA’s Consumer Service Manual says complaints are registered at the sub-divisional office, a Customer Service Centre or a One Window Operation counter. A short written application works well:
- Write your name, address, reference number and meter serial number.
- Describe the fault, for example “meter display blank since 3 March”.
- Attach a copy of your bill and your meter photos.
- Get a receiving stamp or diary number on your copy.
Follow Up on Your Complaint
Keep your complaint number and receiving copy together. If nothing happens, return to the SDO office or Customer Service Centre with these details and ask about the status of your IESCO meter replacement. If the complaint stays unresolved, you can escalate it to NEPRA, which handles consumer complaints against distribution companies.
What Happens After Your Complaint
Once registered, the complaint moves from inspection to installation and then billing adjustment.
Inspection and Accuracy Checks
IESCO staff will check the meter on site. If you doubt the accuracy of a working meter rather than reporting a clear fault, you can request a formal check. The Consumer Service Manual sets a meter challenge fee of Rs500 for single phase and Rs1,000 for three phase, and the meter must be checked in your presence within seven working days of payment. A meter found running fast is replaced at the company’s cost, and excess units are credited for up to two previous billing cycles.
Installation of the New Meter
An IESCO meter change for a faulty meter should not take months. The rules require a defective or burnt meter to be replaced immediately, or within two billing cycles if meters are not available. Billing complaints about defective meters also carry a requirement for replacement as soon as possible and no later than two billing cycles. Where IESCO does not have meters in stock, the consumer may be asked to buy one from an IESCO-approved vendor. Confirm this with your SDO office before buying anything, and never buy a meter from an unapproved seller.
Recording the New Meter Reading and Verifying the Replacement
When the new meter is installed, check these points before the team leaves:
- Note the final reading of the old meter, if readable, and the starting reading of the new meter.
- Photograph both meters, including the new meter serial number.
- Check that the new meter is sealed and the terminal cover is in place.
- On your next bill, confirm the new meter serial number and that the previous reading matches the new meter’s starting reading.
If the next bill still shows the old meter number or an unexpected starting reading, report it at the SDO office with your photos.
IESCO Defective Meter Bill: Average Billing Explained
While a meter is faulty, IESCO cannot bill on an actual reading. The rules for an IESCO defective meter bill protect both the company and the consumer.
How Average Billing Works
Under NEPRA’s Consumer Service Manual, if a meter becomes defective or burnt but was recording correctly up to the last billing cycle, the company may bill on average consumption for up to two months. The average is the higher of:
- 100% of consumption in the same month of the previous year, or
- the average of the last eleven months.
Example: Last March you used 260 units, and your average over the last eleven months is 230 units. Your average bill for March would be based on 260 units, the higher figure. No back-billing is allowed if the meter was correct up to the last billing cycle. If your premises were unoccupied and you can prove it with documents, only minimum charges are payable during average billing.
Display Wash and Data Retrieval
When a meter’s display is washed out, IESCO may retrieve the stored data and bill your actual consumption after notifying you, adjusting the average bills already issued. If the data is not retrieved within three months of replacement, the account cannot be charged for those units. If the meter is sent to the manufacturer, this window extends to six months. Keep your bills from this period so you can check any later adjustment.
Meter Cost, Negligence and Tampering
Who pays for IESCO meter replacement depends on why the meter failed.
Who Pays the Meter Cost
| Situation | Who bears the cost |
|---|---|
| Meter defective, burnt or display-washed for reasons other than consumer fault | IESCO |
| Meter slow because of age, or running fast | IESCO |
| Defect caused by consumer fault, such as overloading or internal wiring defects | Consumer |
| Meter stolen or damaged in an accident while on the consumer’s premises | Consumer |
| Meter on IESCO’s pole or structure, stolen or damaged | IESCO |
When the consumer pays, the company may recover the cost through a demand notice or on the electricity bill. The amount depends on the meter type (single phase, three phase or TOU) and the current price, so ask your SDO office for the written charge before paying. If you pay through a demand notice, keep the bank receipt.
Normal Defect vs Consumer Negligence
A normal defect happens through age, manufacturing faults or supply problems. Negligence includes overloading the connection beyond its sanctioned load or faulty internal wiring that damages the meter. Consumers are liable for damage to company meters caused deliberately or through negligence. Keeping your load within the sanctioned limit and using a licensed electrician protects you from these charges.
Tampering Offence and Its Consequences
Tampering is completely different from a fault. Signs the rules treat as possible tampering include a broken or bogus terminal cover seal, holes in the meter body, a tilted or loose meter, broken glass, or a meter running in reverse. In such cases the company must secure the meter in the consumer’s presence, take photos or video, and give the consumer seven days to reply before any detection bill. After a detection bill is paid, the tampered meter is replaced at the consumer’s cost.
Tampering is also a criminal matter. Under the Criminal Law (Amendment) Act, 2016, meter tampering by domestic consumers is punishable under Section 462-J of the Pakistan Penal Code with up to two years’ rigorous imprisonment, a fine of up to Rs1 million, or both. Never let anyone open, move or “fix” your meter except IESCO staff.
Frequently Asked Questions
How do I report a faulty IESCO meter?
Call IESCO helpline 118 for a complaint number, then submit a written application with your bill and meter photos at your SDO office or Customer Service Centre.
How long does IESCO take to change a defective meter?
NEPRA rules require a defective or burnt meter to be replaced immediately, or within two billing cycles if meters are not available.
Do I have to pay for a new meter?
Not if the meter failed for reasons other than your fault. You pay if the damage came from overloading, internal wiring faults, an accident on your premises or tampering.
How is my bill calculated while the meter is faulty?
IESCO may charge average billing for up to two months, using the higher of last year’s same-month units or the last eleven months’ average.
What should I check after the new meter is installed?
Photograph the new meter’s serial number and starting reading, check the seal, and confirm both appear correctly on your next bill.
Conclusion
IESCO meter replacement is straightforward when you follow the right steps. Spot the fault early, keep your reference number, meter serial number and dated photos ready, then register a 118 complaint and a written application at your SDO office. Understand average billing while you wait, check who bears the meter cost, and verify the new meter reading on your next bill. Avoid any tampering and keep your load within limits, so every IESCO meter replacement protects both your bills and your safety.



